MHD F+G Series

The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability.

---------------------------------------------

Full OBD Flashing:

You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary.

---------------------------------------------

Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost:

N55 EWG (Vehicles built after 07/2013 with electronic wastegate):

- Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i)

- Stage 2 (up to 390HP/580NM)

- Stage 2+ (up to 430HP/630NM)

- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%

N55 PWG (pneumatic wastegate):

- Stage 1 (up to 340HP/540NM)

- Stage 2 (up to 370HP/580NM)

- Stage 2+ (up to 400HP/630NM)

- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%

S55 (BMW M3 / M4 F8x):

- Stage 1 (up to 530HP/700NM)

- Stage 2 (up to 560HP/780NM)

- Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30%

B58:

- Stage 1 (up to 420HP/580NM)

- Stage 2 (up to 470HP/630NM)

- Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30%

---------------------------------------------

Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance!

These are some of the available monitors:

- Boost, Boost Target

- Lambda (AFR)

- Intake Air Temp (IAT)

- Ignition Timing per Cylinder

- Coolant Temperature

- Oil Temperature, Oil Pressure

- Transmission Temperature

- High Pressure Fuel Pump (HPFP)

- Throttle Position

- Wastegate Duty-Cycle (WGDC)

- RPM

- Speed

- EGT

And many more…

MHD exclusive advanced monitor:

- Timing Corrections per Cylinder

- Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't)

- Base Compressor Axis: Boost Setpoint, MAF req WGDC.

- Active Torque Limiters

And many more…

---------------------------------------------

These flash options can be applied to any map directly through the app:

- Exhaust Burble (duration & aggressiveness, min speed, min rpm)

- N20 Map Sensor (on N55)

- Remove top speed limiter (Vmax)

- Cold start noise reduction

- Exhaust flap open in sport mode

- Limit power per gear

- XHP TCU flash support (optimizied OTS maps)

- Sport cooling mode for increased water / air intercooler cooling (B58 only)

---------------------------------------------

Supported Cars:

M135i F2x N55 2012 - 2016

M235i F2x N55 2013 - 2016

M2 F87 N55 2015 - 2018

335i N55 F3x 2011 - 2015

435i N55 F3x 2013 - 2016

535i / GT N55 F1x 2010 - 2017

640i N55 F0x 2011 - 2017

740i N55 F0x 2012 - 2015

X3 35i N55 F25 2010 - 2017

X4 35i / M40i N55 F26 2014 - 2018

X5 40i N55 F15 2013 - 2018

X6 40i N55 F16 2014 - 2018

M3 S55 F80 2014 - 2019

M4 S55 F82 2014 - 2019

M4 S55 F83 2014 - 2019

M140i F2x 2012 - 2019

M240i F2x 2016 - 2019

340i F3x 2015 - 2019

440i F3x 2016 - 2019

540i G3x 2017 -

640i GT G32 2017 -

740i G1x F0x 2015 -

X3 M40i G01 2017 -

X4 M40i G02 2018 -

X5 40i G05 2018 -

Z4 M40i G29 2019 -

114i F2x 2012 - 2015

116i F2x 2011 - 2015

118i F2x 2011 - 2016

120i F2x 2015 - 2017

316i F3x 2012 - 2018

X-Drive is supported on all cars.

All performance power kit cars are supported.

Check out our homepage / user manual for more information and recommended modifications for each stage.

MHD Flaşör F + G Serisi, BMW'niz için eksiksiz bir flaş ayarlama uygulamasıdır. Bir piggyback modülünün aksine, tüm OEM güvenlik mekanizmalarını korurken tamamen DME yeniden kapama yeteneğine sahiptir. Bu, maksimum performans, maksimum güvenlik ve rakipsiz sürüş kolaylığı sağlar.

---------------------------------------------

Tam OBD Yanıp Sönen:

MHD'yi doğrudan evde kurabilir ve hemen ayarlamaya başlayabilirsiniz! Pahalı bir “kilit açma” için DME'nizi çıkarmanıza ve göndermenize gerek yoktur. K + DCAN kablosu ile Android cihazınıza bağlanan MHD Flasher F Serisi uygulamasını indirmeniz ve uygulamanızın OBD-II portuna uygulamanız yeterlidir. ve 15-25 dakika içinde ilk kurulum tamamlanmıştır. Diğer harita değişiklikleri çok daha hızlı - sadece 1-3 dakika! Aracınızı herhangi bir noktada fabrika OEM flaşına geri döndürebilirsiniz ve ilk yedekleme gerekmez.

---------------------------------------------

Aşama 1, Aşama 2 ve E85 OTS (Rafsız) PureBoost'un Haritaları:

N55 EWG (07/2013 tarihinden sonra elektronik atık kapağına sahip araçlar):

- Aşama 1 (360HP / 540NM'ye kadar) (M2 ve X4 M40i için mevcut değil)

- Aşama 2 (390HP / 580NM'ye kadar)

- Aşama 2+ (en fazla 430HP / 630NM)

- Etanol Karışımı Haritaları:% 20'lik etanol karışımları için Aşama 1, 2 ve 2+ E20 Haritaları

N55 PWG (pnömatik atık kapağı):

- Aşama 1 (340HP / 540NM'ye kadar)

- Aşama 2 (370HP / 580NM'ye kadar)

- Aşama 2+ (en fazla 400HP / 630NM)

- Etanol Karışımı Haritaları:% 20'lik etanol karışımları için Aşama 1, 2 ve 2+ E20 Haritaları

S55 (BMW M3 / M4 F8x):

- Aşama 1 (530HP / 700NM'ye kadar)

- Aşama 2 (560HP / 780NM'ye kadar)

- Etanol Karışımı Haritaları:% 30'luk etanol karışımları için Aşama 1, 2 ve 2+ E30 Haritaları

B58:

- Aşama 1 (en fazla 420HP / 580NM)

- Aşama 2 (470HP / 630NM'ye kadar)

- Etanol Karışımı Haritaları:% 30 etanol karışımları için Aşama 1, 2 Harita

---------------------------------------------

Yapılandırılabilir ve çok hassas bir ölçüm düzeni kullanarak kusursuz şekilde çalıştığından emin olmak için motor davranışınızı izleyin. 50+ motor parametreleri bir bakışta mevcut!

Bunlar mevcut monitörlerden bazıları:

- Artır, Hedefi Artır

- Lambda (AFR)

- Emme Hava Sıcaklığı (IAT)

- Silindir Başına Ateşleme Zamanlaması

- Soğutucu Sıcaklığı

- Yağ Sıcaklığı, Yağ Basıncı

- İletim Sıcaklığı

- Yüksek Basınçlı Yakıt Pompası (HPFP)

- Gaz Kelebeği Konumu

- Atık Kapısı Görev Döngüsü (WGDC)

- RPM

- Hız

- EGT

Ve daha fazlası…

MHD özel gelişmiş monitör:

- Silindir Başına Zamanlama Düzeltmeleri

- 22x psi'den daha yüksek okuyabilen EX hedefini artırın (BMW boost hedef kanalı olamaz)

- Baz Kompresör Ekseni: Ayar Noktasını Arttırın, MAF req WGDC.

- Aktif Tork Sınırlayıcıları

Ve daha fazlası…

---------------------------------------------

Bu flaş seçenekleri doğrudan uygulama aracılığıyla herhangi bir haritaya uygulanabilir:

- Egzoz Burble (süre ve saldırganlık, min hızı, min rpm)

- N20 Harita Sensörü (N55’te)

- Üst hız sınırlandırıcısını (Vmax) çıkarın

- Soğuk başlangıçta gürültü azaltma

- Spor modunda egzoz kapağı açık

- Dişli başına sınır gücü

- XHP TCU flaş desteği (optimize edilmiş OTS haritaları)

- Artan su / hava ara soğutucusu soğutması için spor soğutma modu (sadece B58)

---------------------------------------------

Desteklenen Arabalar:

M135i F2x N55 2012 - 2016

M235i F2x N55 2013 - 2016

M2 F87 N55 2015 - 2018

335i N55 F3x 2011 - 2015

435i N55 F3x 2013 - 2016

535i / GT N55 F1x 2010 - 2017

640i N55 F0x 2011 - 2017

740i N55 F0x 2012 - 2015

X3 35i N55 F25 2010 - 2017

X4 35i / M40i N55 F26 2014 - 2018

X5 40i N55 F15 2013 - 2018

X6 40i N55 F16 2014 - 2018

M3 S55 F80 2014 - 2019

M4 S55 F82 2014 - 2019

M4 S55 F83 2014 - 2019

M140i F2x 2012 - 2019

M240i F2x 2016 - 2019

340i F3x 2015 - 2019

440i F3x 2016 - 2019

540i G3x 2017 -

640i GT G32 2017 -

740i G1x F0x 2015 -

X3 M40i G01 2017 -

X4 M40i G02 2018 -

X5 40i G05 2018 -

Z4 M40i G29 2019 -

114i F2x 2012 - 2015

116i F2x 2011 - 2015

118i F2x 2011 - 2016

120i F2x 2015 - 2017

316i F3x 2012 - 2018

X-Drive tüm araçlarda desteklenir.

Tüm performans güç kiti arabaları desteklenir.

Her aşama için daha fazla bilgi ve önerilen değişiklikler için ana sayfamıza / kullanım kılavuzumuza bakın.

The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability.

---------------------------------------------

Full OBD Flashing:

You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary.

---------------------------------------------

Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost:

N55 EWG (Vehicles built after 07/2013 with electronic wastegate):

- Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i)

- Stage 2 (up to 390HP/580NM)

- Stage 2+ (up to 430HP/630NM)

- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%

N55 PWG (pneumatic wastegate):

- Stage 1 (up to 340HP/540NM)

- Stage 2 (up to 370HP/580NM)

- Stage 2+ (up to 400HP/630NM)

- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%

S55 (BMW M3 / M4 F8x):

- Stage 1 (up to 530HP/700NM)

- Stage 2 (up to 560HP/780NM)

- Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30%

B58:

- Stage 1 (up to 420HP/580NM)

- Stage 2 (up to 470HP/630NM)

- Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30%

---------------------------------------------

Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance!

These are some of the available monitors:

- Boost, Boost Target

- Lambda (AFR)

- Intake Air Temp (IAT)

- Ignition Timing per Cylinder

- Coolant Temperature

- Oil Temperature, Oil Pressure

- Transmission Temperature

- High Pressure Fuel Pump (HPFP)

- Throttle Position

- Wastegate Duty-Cycle (WGDC)

- RPM

- Speed

- EGT

And many more…

MHD exclusive advanced monitor:

- Timing Corrections per Cylinder

- Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't)

- Base Compressor Axis: Boost Setpoint, MAF req WGDC.

- Active Torque Limiters

And many more…

---------------------------------------------

These flash options can be applied to any map directly through the app:

- Exhaust Burble (duration & aggressiveness, min speed, min rpm)

- N20 Map Sensor (on N55)

- Remove top speed limiter (Vmax)

- Cold start noise reduction

- Exhaust flap open in sport mode

- Limit power per gear

- XHP TCU flash support (optimizied OTS maps)

- Sport cooling mode for increased water / air intercooler cooling (B58 only)

---------------------------------------------

Supported Cars:

M135i F2x N55 2012 - 2016

M235i F2x N55 2013 - 2016

M2 F87 N55 2015 - 2018

335i N55 F3x 2011 - 2015

435i N55 F3x 2013 - 2016

535i / GT N55 F1x 2010 - 2017

640i N55 F0x 2011 - 2017

740i N55 F0x 2012 - 2015

X3 35i N55 F25 2010 - 2017

X4 35i / M40i N55 F26 2014 - 2018

X5 40i N55 F15 2013 - 2018

X6 40i N55 F16 2014 - 2018

M3 S55 F80 2014 - 2019

M4 S55 F82 2014 - 2019

M4 S55 F83 2014 - 2019

M140i F2x 2012 - 2019

M240i F2x 2016 - 2019

340i F3x 2015 - 2019

440i F3x 2016 - 2019

540i G3x 2017 -

640i GT G32 2017 -

740i G1x F0x 2015 -

X3 M40i G01 2017 -

X4 M40i G02 2018 -

X5 40i G05 2018 -

Z4 M40i G29 2019 -

114i F2x 2012 - 2015

116i F2x 2011 - 2015

118i F2x 2011 - 2016

120i F2x 2015 - 2017

316i F3x 2012 - 2018

X-Drive is supported on all cars.

All performance power kit cars are supported.

Check out our homepage / user manual for more information and recommended modifications for each stage.